Differences

This shows you the differences between two versions of the page.

--- digistar [2026/01/07 16:28] – created protocol
+++ digistar [2026/05/20 10:46] (current) – protocol
@@ Line 1: / Line 1: @@
 <code>
-digistar#onu show discovered
+Para conectar:
+telnet 10.3.100.3
+senha: admin
+digite: enable
+senha: digistar
+Para ver as CPE para provisionar digite:
+onu show discovered
 Link 3:
     Serial Number
 ITBS5b0e62b7
-digistar#onu set ?
+Para ativar a CPE digite: (pode usar as teclas TAB e ? para auto-preencher)
-  <1-4>/<1-128>  Link/Onu
-/16
-  range          Sets a range of onus on specific link with a discovered serial
-digistar#onu set 3/16 ?
+onu set 3/16 ITBS5b0e62b7
-  AAAAXXXXXXXX  GPON Serial Number of ONU
-    ITBS5b0e62b7
-digistar#onu set 3/16
+Aqui a CPE esta na PON 3 com ID 16.
-  AAAAXXXXXXXX
+o gem vai ser 5+ID da CPE, no caso: 516.
-digistar#onu set 3/16 ITBS5b0e62b7 ?
-  us-fec  Use upstream FEC
-  <cr>
-digistar#onu set 3/16 ITBS5b0e62b7
-digistar#
+Para ativar o servço para ONU digite:
-digistar#bridge add gpon-3 onu 16 gem 2 gtp 1 vlan 101 br_mode eth 1
+bridge add gpon-3 onu 16 gem 516 gtp 1 vlan 101 br_mode eth 1
+Para ativar o servço para ONT digite:
+bridge add gpon-3 onu 16 gem 516 gtp 1 vlan 101 rg_mode eth 1
 </code>
+===== extract ONU =====
+<code>
+for i in $(grep eth ds|cut -d "-" -f 7| tr ' ' '\n' | grep -vE 'UP|DOWN'|sort); do echo $i; done
+for i in $(grep eth ds10|cut -d "-" -f 7| tr ' ' '\n' | grep -vE 'UP|DOWN'|sort); do echo -e "set whitelist phy_addr address $i password null action add slot 11 pon 10 onu null type 5506-01-A1\n"; done
+</code>
+===== Digistar to Fiberhome =====
+<code>
+onu
+for i in $(grep eth ds10|cut -d "-" -f 7| tr ' ' '\n' | grep -vE 'UP|DOWN'|sort); do echo -e "set whitelist phy_addr address $i password null action add slot 11 pon 10 onu null type 5506-01-A1\n"; done
+for i in $(seq -s " " 1 12); do echo -e "set epon slot 11 p 10 o $i p 1 serv number 1\nset epon slot 11 p 10 o $i p 1 service 1 vlan_mode tag 0 33024 110\napply onu 11 10 $i vlan\n"; done
+ont
+for i in $(grep veip ds10|cut -d "-" -f 7| tr ' ' '\n' | grep -vE 'UP|DOWN'|sort); do echo -e "set whitelist phy_addr address $i password null action add slot 11 pon 10 onu null type HG260\n"; done
+for i in $(seq -s " " 13 20); do echo -e "set ep slot 11 pon 10 onu $i p 1 onuveip 1 33024 110 65535 33024 65535 65535 33024 65535 65535 0 1 65535 servn null \n"; done
+</code>